Quickie Groove Technical Information Seite 24
- Seite / 66
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
24 Quickie Groove
.EMS
6.7 Optima backrest upholstery
GROOVE can be supplied with optima backrest upholstery,
which can be adjusted in tension to the individual’s requirements
(Fig. 6.8).
To change the shape and/or tension of the ‘Optima’ backrest,
remove the padded cover from the rear of the backrest and
expose the tension straps. Loosen or tighten the straps to suit.
(The most comfortable and supportive position is achieved with
the wheelchair user seated in the chair).
WARNING!
Ensure the straps are securely fastened and replace the padded
cover prior to use.
6.8 Manual adjustable backrest (manual recline)
For depth adjustment see section 6.3.
To recline the backrest angle, pull the lever at the top of the
backrest which operates the gas strut. Hold the lever and adjust
the back angle required. If you release the lever, the angle will
stay in the adjusted position. If you want to adjust the backrest
into the upright position, you might need to support the upward
motion (Fig. 6.9).
6.9 Manual angle adjustment of the xed back
To adjust the back angle, release the two outer screws of the
back adapter plate on both sides of the frame. After removing
the screws you can set the back angle between -3°(degrees) and
12° in 3° steps. Then retighten the outer screws in the adapter
plate (Fig. 6.10).
6.10 JAY backrests
The standard backrest assembly will allow the fitting of a JAY
backrest, which is available as an optional extra.
6.11 Headrest
To fit the headrest, fit the location bracket to the backrest brace,
using the screws and nuts supplied, ensuring that they are fully
tightened.
The headrest height is changed by loosening the adjustment
lever and sliding the inner vertical tube to the desired position
and tightening the lever mechanism. The headrest to seat depth
is adjusted by loosening the 6mm Allen screws and moving the
hinge to the desired position and then tightening the screws
securely. To adjust the headrest angle, loosen the screws at
the headrest upholstery, position the headrest as required and
tighten the screws securely.
6.12 Manual setting of the seat angle on the Groove
To set the seat angle, release the bolt fixing the “Banana”
bracket between the seat interface module and the seat packer
module. Set the seat angle at 0°, 3° or 6° and 9°, then replace
and re tighten the bolt between the seat interface module and the
seat packer module. (Fig. 6.11).
6.13 Powered Seating
WARNING!
The Groove F-XL cannot be fitted with powered •
options.
It is possible to reverse the direction of an actuator relative •
to the direction of the joystick. Ensure you know which
direction to move the joystick for the desired operation.
Failure to do so may result in damage and/or injury.
Powered seat functions can be operated in “latched” mode. •
To stop a latched seat function before the end of travel,
operate the joystick in the reverse direction.
Fig. 6.8
Fig. 6.10
Fig. 6.9
Fig. 6.11
6°
9°
0°
3°
- Instructions for Use 1
- User Information 2
- Quickie Groove 3 3
- Rear/Front Wheel Drive 5
- Mid Wheel Drive 5
- 1.0 Your Wheelchair 6
- 2.0 How to use this manual 6
- Quickie Groove 7 7
- 8 Quickie Groove 8
- 3.2 Label explanations 8
- WARNING!WARNING! 9
- Fig. 4.1 10
- Fig. 4.2 10
- Fig. 4.5 11
- Fig. 4.4 11
- Quickie Groove 12
- Quickie Groove 13 13
- Fig 4.6 and Fig 4.7) 15
- (RWD base only) 16
- and removal procedure 16
- Quickie Groove 17 17
- 5.5 and Fig. 5.6) 18
- Fig. 5.8) 19
- Fig. 5.9) 19
- Fig. 5.18 21
- Fig 5.19): 22
- 6.0 Seating 23
- Fig. 6.8) 24
- Quickie Groove 25 25
- Quickie Groove 27 27
- WARNING! 28
- Quickie Groove 29 29
- Fault code Possible cause 30
- 9.0 R-net Control System 31
- Fig.10.3 33
- Fig. 10.4 34
- Fig.11.1 35
- Fig. 11.2 35
- 12.0 Batteries and charging 37
- Fig. 12.8 39
- Fig. 12.7 39
- 13.0 Transportation 41
- Quickie Groove 43 43
- Quickie Groove 45 45
- Quickie Groove 47 47
- Quickie Groove 49 49
- Fig. 13.55 50
- Fig. 13.56 50
- Fig. 13.57 50
- Fig. 13.58 50
- Fig. 14.1) 51
- Fig. 14.2) 51
- Fig. 14.3) 51
- Fig. 14.4) 51
- Fig. 14.5 52
- Fig. 14.6 52
- Fig. 14.7 52
- Fig. 14.8 52
- Fig. 14.9 53
- Fig. 14.10 53
- Fig. 14.12 53
- Fig. 14.13 53
- Fig. 14.11 53
- Quickie Groove 55 55
- Fig. 14.18 57
- Fig. 14.19 57
- Quickie Groove 59 59
- Quickie Groove 61 61
- 16.0 Service History 63
- 17.0 Disposal 63
- Quickie Groove 65 65
- Pt.No.000690665 66
Verwandte Produkte und Handbücher für Nein Quickie Groove
Nein Quickie Pulse Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Nein Quickie QRi Bedienungsanleitung
(5 Seiten)
(5 Seiten)
Nein Quickie QM-7 Series Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Nein Quickie QRi Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Nein Quickie Pulse Bedienungsanleitung
(9 Seiten)
(9 Seiten)
Nein Quickie Jive Spezifikationen
(60 Seiten)
(60 Seiten)
Nein Quickie Rhythm Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Nein Quickie Q7 Adjustable Bedienungsanleitung
(24 Seiten)
(24 Seiten)
Nein Quickie Argon2 Bedienungsanleitung
(38 Seiten)
(38 Seiten)
Nein Quickie Salsa M Bedienungsanleitung
(170 Seiten)
(170 Seiten)
Nein Quickie S-636 Bedienungsanleitung
(7 Seiten)
(7 Seiten)
Nein Quickie Rumba Modular Bedienungsanleitung
(86 Seiten)
(86 Seiten)
Nein Quickie S-646 SE Bedienungsanleitung
(20 Seiten)
(20 Seiten)
Nein Quickie Xenon SA Bedienungsanleitung
(8 Seiten)
(8 Seiten)
Nein Quickie Groove Bedienungsanleitung
(355 Seiten)
(355 Seiten)
Nein Quickie Jive Bedienungsanleitung
(196 Seiten)
(196 Seiten)
Nein Quickie 2HP Bedienungsanleitung
(4 Seiten)
(4 Seiten)
Nein Quickie Hula Bedienungsanleitung
(4 Seiten)
(4 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern